Knowing The Benefits And History Of Automotive Windshields

Automotive windshields are large pieces of safety glass that are installed on different forms of vehicles. They come equipped on cars, buses, planes and even some motorcycles. The glass used is usually lamented. This means the glass was treated with two sheets of curved glass separated by a sheet of plastic before it was glued and sealed down to a window frame.

Windshields were created to protect automobile occupants from environmental elements. It has been used to shelter people from both snow and rain. It also protect occupants from the wind and debris that may be in the air. It is effective in keeping out harmful ultraviolet rays since many vehicles come equipped with a special coating of UV. It is similar to the coating used on standard sunglasses with or without the tint.

When the original car was created, windshields were created out of pure glass. When the glass is not lamented, it can cause a severe risk to passengers in the event of an accident. It was not until a series of incidents that glass windows were replaced with a material much stronger and safer. With a tougher glass, it would shatter into harmless little pieces in the event of an accident. This would cause far less damage to drivers and passengers.

The first lamented windshield was first created in France. It used a cellulose middle layer instead of conventional plastic. The cellulose layer was very effective in holding the two layers of glass together when an accident occurred. It was not until many years later that plastic became a better alternative. The purpose was to ensure that windshields will not break when an accident occurred.

Having windshields on motorcycles is becoming more popular today as people are becoming more socially aware and responsible. A typical windshield is large enough to protect both a person’s face and torso from carelessly discarded cigarettes. The discarded cigarettes has been a constant problem for bike riders that have to deal with burns and ashes left behind. It can also protect against other air and wind borne elements and debris.

Before, a bike rider had to look over his/her windshield because it did not provide enough clarity. That has all changed and manufactures have created better windshields with better material. Now a good windshield can redirect noise, airflow and low-pressure turbulence. This makes a motorcycle ride more enjoyable and safer since riders reduce the chance of suffering from wind fatigue.

Polycarbonate windshields are currently a new and better material available for automobile owners. Makers of the innovative product have tested it to ensure customers with the best material available that is both chemical and impact resistant. It has been tested under the pressures of steel wool to guarantee the effectiveness in protection and resistance. Optical clarity is also many times better than original lamented glass shields. It is currently only approved in the motorcycle industry but people can still obtain the replacement for other forms of vehicles since it is in compliance with state requirements.

Laminated polycarbonate windshields are made differently from commercial ones more readily available. The layers include a flexible polymer substrate rather than plastic. A chemical and scratch resistant coating is applied with a special adhesive in between two layers of polycarbonate sheets. Each layer is then treated to become transparent for people’s safety.

Another option that people have is the use of tinted windows to protect from sun glare. The law places heavy restrictions on the use of heavily tinted glass windows. There is a maximum level of tint permitted and exceeding that limit can lead to multiple consequences other than being fined. If necessary for sun glare protection, drivers should consider having the uppermost part of their window more noticeably tinted.

Thermal glass has also been used in the past. This was a popular option before the invention of navigational systems. As of now, thermal glass can potential prevent many navigational systems from working because the metal embedded into the glass blocks the signal communication between a satellite and the device. People that have thermal glass can decide to buy an external antenna for their device to resolve this particular issue.

Automotive windshields have come a long way in history. They have evolved and changed to adapt to the needs of people overtime. People can obtain greater benefits if they properly accommodate their vehicles to adapt to their particular needs. Custom and special applications can be done to automobiles as long as they do not violate the law or the maximum restrictions.

Automotive Equipment and Tools For The Automotive Industry

The automotive equipment industry deals with the production of every kind of tool and machinery that is needed for the manufacture, maintenance and repair of vehicles including cars and car parts. As such, the industry produces several different varieties of equipment starting from basic hand tools to more complex machinery.

Different Kinds of Automotive Equipment

Automotive workshops and garages will be unable to function without automotive equipment. Shop furniture, lifts, exhaust hoses, air compressors, lubrication equipment, electric and light reels, jacks, vehicle servicing equipment, fluid storage tanks and trans-air piping are some of the many different types of automotive equipment that are used by automotive manufacturing and automotive repair businesses.

Common Types Of Automotive Equipment

* Hand Tools: Automotive repair shops use several different types of hand tools for their repair and maintenance projects. Some of the commonest items include ratchet sets and wrench sets, crowbars (also known as pry bars), socket sets, screwdrivers, star and clutch-head drivers, hammers, pliers and wire cutters, electric drills, hacksaws and torque wrenches.

* Pneumatic Tools: Most automotive workshops now use pneumatic tools as an alternative to electricity powered motors because the latter is more prone to fire hazards. Such tools are powered by compressed air and are high powered versions of the more traditional hand tools. Common examples of pneumatic automotive equipment include air compressors that can be used to power a variety of tools including hammers, drills, ratchets and spraying tools.

* Availability of pneumatic equipment makes it easier for mechanics and technicians to undertake repair and maintenance work because they are powerful and easy to use. For example, a set of pneumatic shears can cut through sheet metal at a faster rate and leave behind a smoother edge when compared to traditional tin snips. Similarly, air hammers outfitted with chisel or punch bits have multiple uses. They can they be used for straightening dents. The chisel feature can be used to break rusted parts loose and the punch bits can be used to remove old rivets and bolts that are too difficult to take out by hand.

* Lifts: several different kinds of lifting equipment are used to lift and secure cars so that mechanics and repair persons can easily work under the vehicle. These lifting tools include both low-tech tools such as basic floor jacks, car ramps and jack stands as well as hydraulic lifts and floor jacks for better efficiency and performance.

* Vehicle Exhaust Removal Systems: vehicle exhaust removal systems are used to capture and remove harmful exhaust fumes to insure optimal air quality in automotive maintenance and repair facilities. These are mandatory equipment as per OSHA Standards in order to limit exposure to harmful vehicular emissions. Common vehicle exhaust removal systems include hose drops as well as reels.

* Lubrication Systems: Automotive lubrication systems include several different types of oil meters, ATF meters, gear lube meters, dispense valves and grease dispenses valves.

The Automotive equipment business is a very large and competitive business. Automotive repair businesses must buy equipment from reputable dealers for the best deals and performance levels.

Road Trip Preparation Prevent Unexpected Automotive Repair

If you are preparing for a day-trip or an extended vacation to unwind, having a “pre-trip” automotive service will ease your mind and possibly prevent an unexpected automotive repair that leaves you stranded out in the cold. Here is a simple check list to include in an automotive service to get you off to a great start:

* Vehicle Loading & Tire Inspection

Virtually all late model motor vehicles are equipped with a sticker located on the driver’s door or pillar. That sticker determines maximum vehicle capacity, which means the weight of the vehicle along with the combined weight of passengers and cargo. Don’t exceed the recommended load capacity. On the same sticker is also a tire pressure chart. Be sure to check all tires and make certain they are inflated properly. Tire tread depth should also be inspected. If tires are worn to a point where less than 2/32-inch of the tread remains, or if the cord or fabric is showing, it’s time to replace the tires.
* Lights & Horn

Inspect all exterior and interior light/lamp functions. If any bulbs are burned out, and if you are uncomfortable with replacing it yourself, take your vehicle to your automotive service center and have it taken care of. You will want to make sure the horn works properly.
* Windshield Wipers

Test the wiper operation of your vehicle. You will also want to check the wear of the wiper blades. If they are streaking, or squeaking, they probably need to be changed to make sure you have clear visibility in the elements.
* Parking Brake

Test the parking brake with the engine running, transmission in drive and your foot on the brake. With the parking brake engaged slowly release the foot brake. If your vehicle moves forward, then the parking brake is not adequate. To ensure your safety, don’t forget to have it checked as part of the automotive service.
* Spare Tire

Spare tires can lose pressure over time. It’s a good idea to not only check the pressure of the spare, you should also insure it isn’t damaged, as well as checking the tread wear and overall condition.
* Car Jack & Tools

Check the truck to make sure you have the appropriate tools and car jack (and that they are in good working order) for changing flats, etc.

If you have completed the above check-list and had a complete automotive service, make sure you have taken care of any deficient or broken items. Although you can never guarantee that something unforeseen may happen, you will at least be prepared for the unexpected.

Need quality automotive service? Contact our ASE Certified Technicians at Clausen Automotive by calling (608) 221-8321 or go on-line at http://clausenautomotive.com for more information. Since 1975, our family-owned automotive repair shop has proudly served vehicle owners in Madison, WI, and surrounding communities.

Automotive Parts, Aerospace And Marine Parts Ultrasonic Cleaners

Some mechanics have reported a 50% savings in cleaning time by turning to an ultrasonic parts cleaning machine while taking advantage of an ecologically safe alternative to manual cleaning with toxic chemicals. With today’s industrial sized ultrasonic cleaners, the speed of ultrasonic cleaning to remove soils is combined with the capacity to clean multiple parts at once. Let’s take a look at some specific examples of how an ultrasonic cleaner can save time and money while providing a non-toxic solution in the automobile, marine and aviation industries.

There are so many uses for an ultrasonic cleaner in an auto shop. Ultrasonic car parts cleaning saves time by eliminating the need for manual scrubbing of auto parts covered with grease, oil, and other lubricants. Besides freeing up time, the hazardous chemicals can be replaced with biodegradable soaps. Specific examples of items that are commonly cleaned by a benchtop ultrasonic cleaner include filters, shock absorber parts, power steering parts, pistons, valves, fuel injectors, bearings just to name a few. Larger industrial-sized units can be used for ultrasonic carburetor cleaning and ultrasonic exhaust manifold cleaning, where cleaning action is needed deep within the network of passages. This large capacity also allows for ultrasonic crankshaft cleaning and ultrasonic cylinder block cleaning as well the means to clean multiple parts at once.

For marine mechanics, an ultrasonic cleaner can clean virtually any part within minutes and also provides an alternative to using toxic cleaning agents. When cleaning marine inboard and outboard motors, a cleaning solution that is both thorough and gentle is necessary because many parts are made out of Ultrasonic Auto Engine Parts Ultrasonic Cleaneraluminum. Not only do these parts need to be cleaned, but they need to be cleaned in a way that prevents future corroding. An ultrasonic boat part cleaner is the answer because ultrasonic cleaning is gentle enough to not harm the parts yet powerful enough to remove the soil. As with cars, an ultrasonic carburetor cleaner is employed to clean the carburetors from boat motors as well.

For aircraft mechanics, carbon deposits can present a cleaning challenge. Ultrasonic aircraft parts cleaning not only readily removes carbon deposits, but speeds up the cleaning process considerably and is much safer than working with the toxic chemicals previously used. An industrial-sized ultrasonic aircraft parts cleaner can accommodate large parts or multiple parts, including fuel nozzles, brake parts, turbine blades, and generator components. Parts are thoroughly cleaned and restored to their original condition, which is especially important in aircrafts.
Ultrasonic cleaners can help address many issues that mechanics face today: the need to save time and money and to protect both workers and the environment. By using an ultrasonic cleaner, the process of cleaning engine parts is greatly accelerated and expensive, toxic chemicals are replaced by a cost-effective, environmentally friendly alternative.

MAHA USA Automotive Lifts Solutions

With over 40 years of experience, MAHA USA is the premier US manufacturer of German-engineered automotive lifts. Their renowned technology and reputation for quality has made their automotive lifts some of the best across the board, used by automotive repair shops, car dealership service facilities, and OEMs.

MAHA USAs automotive lifts meet strict industry standards and are famous for their high quality designs and safety features. From drawing board to assembly line, their automotive lifts are relied upon by major car manufacturers for their reliability and state-of-the-art design.

Now more than ever, automotive lifts are in great demand because people are hanging on to their cars longer, and repairing them, rather than trading them in, or leasing new vehicles. The automotive repair and body shop industries are expanding rapidly, adding more repair bays to handle increased demand. This has simultaneously increased demand for automotive lifts, because it is less costly to make minor repairs, rather than start from scratch with a brand new car. Additionally, people are more conscious of maintenance, using less costly quick-lube service locations, which make good use of automotive lifts, rather than going to a more expensive dealership service centers. MAHA automotive lifts are used by car rental agencies to repair and service their vehicles, and automotive hobby enthusiasts, particularly those who are sticklers about their cars interior parts, as well as its exterior appearance.

MAHA USA manufactures many different types of automotive lifts depending on the needs of their customers. Their automotive lift technology includes two post, four post, and specialty automotive lifts, as well as specialty, in-ground and scissors automotive lifts for cars, light trucks and SUVs. Depending on the type of business, these automotive lifts can be customized to suit the needs of auto repair shops, body shops, neighborhood repair shops, quick lube service centers and dealerships. All you have to do is asses your layout and MAHAs distributors will help you determine which automotive lifts are ideal for your setup.

Once you have determined your needs, you can proceed with opening up a new car repair or body shop, or maybe acquire a quick oil change franchise to add this valuable service to your community. Take advantage of the technology of one of the premier American manufacturers, and put it to good use to rebound during these tough economic times. Getting into the auto service business can be a lucrative endeavor, now that new cars are not as easy to obtain. Having automotive lifts from MAHA USA can ensure a new business venture gets off to a great start, or the expansion of an existing auto body service shop is completed without depleting too much equity from your business.

Automotive lifts from MAHA USA are a wise investment to ensure the success of your existing business, or to get you in on the ground floor of a new venture. Trust the quality from MAHA USA for all your automotive repair needs.